Yahoo Poland Wyszukiwanie w Internecie

Search results

1. reprapy.pl › viewtopicAnycubic I3 Mega nie widzi plików - reprapy.pl

   reprapy.pl › viewtopic

   • Zapisane w pamięci cache

   Witam drukarka anycubic I3 Mega nie widzi więcej niż 4 pliki na karcie sd. Czy można coś z tym zrobić?

2. wiki.anycubic.com › en › resin-3d-printerResin printer:The sliced file cannot be recognized - Anycubic...

   wiki.anycubic.com › en › resin-3d-printer

   • Zapisane w pamięci cache

   1. File format error. Check whether the format of the slice file matches the printer, if not, the printer will be unable to recognize it. The specific file format can be referenced in the table provided below or found in Anycubic Photon Workshop by selecting the corresponding printer model and viewing the sliced file suffix. 2.File naming issues.

3. store.anycubic.com › blogs › 3d-printing-guidesTroubleshooting Guide: File Failed to Be Recognized by ... -...

   store.anycubic.com › blogs › 3d-printing-guides

   • Zapisane w pamięci cache

   6 maj 2023 · The resin printer may not recognize the file format, resulting in the 3D printer not being able to open the file. We need to check the file format and verify if the file is suitable for the resin printer you are using. Solution for file not showing. Check the File Format.

4. www.reddit.com › r › anycubic.STL Files not showing on Anycubic Kobra : r/anycubic - Reddit

   www.reddit.com › r › anycubic

   • Zapisane w pamięci cache

   I found I had this problem when uploading the STL files to the card on a Mac. Even after formatting the card that came with the printer. Even after successfully using the same card to update the firmware on the printer, so I knew it was able to read that card.

5. 3dprinterly.com › how-to-fix-anycubic-photon-mono-x-not-reading-files4 Ways How to Fix Anycubic Photon Mono X Not Reading Files

   3dprinterly.com › how-to-fix-anycubic-photon-mono-x-not-reading-files

   • Zapisane w pamięci cache

   16 paź 2023 · To fix Anycubic Photon Mono X not reading files you’ll need to check file compatibility, make sure the files are not corrupted, and do a USB drive inspection. Doing a firmware update and using a different slicer are also possible solutions to fix this kind of problem.

6. wykop.pl › wpis › 78844423Próbuje przygotować plik elementu na drukarkę 3d. Jednak ... -...

   wykop.pl › wpis › 78844423

   • Zapisane w pamięci cache

   4 lis 2024 · Jednak po eksporcie pliku /stl do oprogramowania AnyCubic nie widać żadnego obiektu. Na wstępie - jestem całkowicie zielony jeśli chodzi o blendera. Moja metodologia pracy do przygotowanie poszczególnych cześci w programie 2d oraz import jako .svg do blendera.

7. www.reddit.com › r › FixMyPrintFiles not appearing on Anycubic i3 Mega : r/FixMyPrint - Reddit

   www.reddit.com › r › FixMyPrint

   • Zapisane w pamięci cache

   Files not appearing on Anycubic i3 Mega. Model: Anycubic i3 Mega. Firmware: 1.1.0. Slicer: Cura 3.4.1. I need a bit of help because I cannot find my gcode files on the printer. I just set up the printer and was able to print the test owl that came on the SD card just fine.